Estate Department, Reserve Bank of India, Kolkata had published Notice Invited Tender (NIT) for Limited tender from the empanelled vendors or firms [Section-A, Trade-01, Category-III, Above Rs.10 (Ten) Lakh to Rs.30 (Thirty) Lakhs] in a short notice for Providing, fabricating, fixing & welding Car shed at BMOP, RBI, Kolkata on January 15, 2020 (E-tender no. RBI/Kolkata/Estate/160/19-20/ET/313) with approval of CGM dated January 10, 2020. The last date of submission of e-tender of the above work has been extended upto February 06, 2020 with the approval of CGM dated January 29, 2020. Part-II Sl. no. 1 of Part-II (Unpriced Bid / Schedule of Quantities) is amended as follows: Original text- Providing, welding, Fabricating & constructing both side cantilever shed by doing electric welding the 4 mm thick solid polycarbonate sheet with necessary MS frame work. The above work should be carried out as per attached sketch & specification are given below :- (A) FRAMING :- (a) Vertical posts are made of 2 nos. 72 x72x4.0 mm MS Black Square tube including 12 mm thick base plate of size 500 x 400 mm duly welded. (5 nos. set) (b) Tube Horizontal Ties (Between two truss) are made of 49.5 x 49.5 x 3.6 mm MS Black Square Tube – 2 nos. (c) Truss are made of with 96 x 48 x 4.0 mm MS Black rectangular tubes as main member. (d) Purlins are made of 49.5 x 49.5 x 3.6 mm MS Black square tube @ 657 c/c. (7 nos.). (e) Providing & welding 10 mm thick (300 x 150 mm) MS plate at the junction of vertical post and base plate. (f) Bracings / Ties are made of 49.5. x 49.5 x 3.6 mm and placed when & where required. (g) Providing & welding 150 mm long black rectangular tube (96 x 48 x4.0) with main truss below purlin (both ends) (h) All junction should be properly welded. B) TOP sheet: Providing & fixing 4 mm thick colour solid polycarbonate sheet of approved make, shade & design over the purlins with necessary screw. C) GUTTER (Dongue): Providing & fixing standard thick polycarbonate or PVC Gutter with necessary m.s. frame work on the both ends. The rate quoted shall include the cost of providing & applying two coats of 1st quality synthetic enamel paint over a coat of metal primer on entire MS framing, providing & grouting the base plate of vertical posts with 8 nos. heavy type screw / nut & fastener, providing 150 mm lap with adjacent sheet while fixing, lifting, scaffolding disposing off the debris out of Banks premises etc. all complete as directed by Banks Engineer-in-Charge. (Plan area measurement will be taken for payment) (Basic rate of 4 mm thick polycarbonate sheet =Rs.1680/- per Sqm excluding GST) Revised Text – Providing, welding, Fabricating & constructing both side cantilever shed by doing electric welding the 4 mm thick solid polycarbonate sheet with necessary MS frame work. The above work should be carried out as per attached sketch & specification are given below :- (A) FRAMING :- (a) Vertical posts are made of 2 nos. 72 x72x4.0 mm MS Black Square tube including 12 mm thick base plate of size 500 x 400 mm duly welded. (5 nos. set) (b) Horizontal Ties (Between two truss) are made of 49.5 x 49.5 x 3.6 mm MS Black Square Tube – 2 nos. (c) Truss are made of with 96 x 48 x 4.0 mm MS Black rectangular tubes as main member. (d) Purlins are made of 49.5 x 49.5 x 3.6 mm MS Black square tube @ 657 c/c. (7 nos.). (e) Providing & welding 10 mm thick (300 x 150 mm) MS plate at the junction of vertical post and base plate. (f) Bracings / Ties are made of 49.5. x 49.5 x 3.6 mm and placed when & where required. (g) Providing & welding 150 mm long black rectangular tube (96 x 48 x4.0) with main truss below purlin (both ends) (h) All junction should be properly welded. B) TOP sheet: Providing & fixing 4 mm thick colour solid polycarbonate sheet of approved make, shade & design over the purlins with necessary screw. C) GUTTER (Dongue): Providing & fixing standard thick polycarbonate or PVC Gutter with necessary M.S. frame work on the both ends. The rate quoted shall include the cost of providing & applying two coats of 1st quality synthetic enamel paint over a coat of metal primer on entire MS framing, providing & grouting the base plate of vertical posts with 8 nos. heavy type screw / nut & fastener, providing 150 mm lap with adjacent sheet while fixing, lifting, scaffolding disposing off the debris out of Banks premises etc. all complete as directed by Banks Engineer-in-Charge. (Plan area measurement will be taken for payment) (Basic rate of 4 mm thick polycarbonate sheet =Rs.1680/- per Sqm excluding GST) (Approx. dimension of Width = 4.6 m, Length = 20 m, Height = 4.0 m) (Sl. no. 2 of Part-II (Unpriced Bid / Schedule of Quantities) is amended as follows: Original text : Providing, welding, Fabricating & constructing one side cantilever shed by doing electric welding the 4 mm thick hollow polycarbonate sheet with necessary MS frame work. The above work should be carried out as per attached sketch & specification are given below:- (a) FRAMING :- (b) Cantilever Truss are made of 96 x 48 x 4.0 mm M.S. Black Rectangular Tube (As per sketch) including 10 mm thick wall plate of size 450 x 150 mm duly welded. (16 nos.) (c) Horizontal Ties (Between two truss) are made of 49.5 x49.5 x 3.6 mm (2 nos.) plus 38 x 38 x 3.2mm (2nos.) MS Black Square Tube – 4 nos. (d) Purlins are made of 49.5 x 49.5 x 3.6 mm MS Black square tube @ 657 c/c. (7 nos.). (e) Providing & welding 10 mm thick MS plate at the junction of cantilever truss and wall plate. (f) Providing & welding 150 mm long black rectangular tube (96 x 48 x4.0) with main truss below purlin (both ends) (g) Bracings / Ties are made of 38x 38x3.2 mm and placed when & where required. (h) All junction should be properly welded. B) TOP sheet: Providing & fixing 4 mm thick colour solid polycarbonate sheet of approved make, shade & design over the purlins with necessary screw. C) GUTTER (Dongue): Providing & fixing standard thick polycarbonate or PVC Gutter with necessary m.s. frame work on the free end. The rate quoted shall include the cost of providing & applying two coats of 1st quality synthetic enamel paint over a coat of metal primer on entire MS framing, providing & grouting the base plate of vertical posts with heavy type 8nos. screw / nut & fastener, providing & fixing providing 150 mm lap with adjacent sheet while fixing, lifting, scaffolding, providing & filling the gap between wall & new shed with approved quality silicon, disposing off the debris out of Banks premises etc. all complete as directed by Banks Engineer-in-Charge. (Plan area measurement will be taken for payment) (Basic rate of 4 mm thick polycarbonate sheet =Rs.1680/- per Sqm excluding GST) Revised Text : Providing, welding, Fabricating & constructing one side cantilever shed by doing electric welding the 4 mm thick Solid polycarbonate sheet with necessary MS frame work. The above work should be carried out as per attached sketch & specification are given below:- (a) FRAMING :- (b) Cantilever Truss are made of 96 x 48 x 4.0 mm M.S. Black Rectangular Tube (As per sketch) including 10 mm thick wall plate of size 450 x 150 mm duly welded. (16 nos.) (c) Horizontal Ties (Between two truss) are made of 49.5 x49.5 x 3.6 mm (2 nos.) plus 38 x 38 x 3.2mm (2nos.) MS Black Square Tube – 4 nos. (d) Purlins are made of 49.5 x 49.5 x 3.6 mm MS Black square tube @ 657 c/c. (7 nos.). (e) Providing & welding 10 mm thick MS plate at the junction of cantilever truss and wall plate. (f) Providing & welding 150 mm long black rectangular tube (96 x 48 x4.0) with main truss below purlin (both ends) (g) Bracings / Ties are made of 38x 38x3.2 mm and placed when & where required. (h) All junction should be properly welded. B) TOP sheet: Providing & fixing 4 mm thick colour solid polycarbonate sheet of approved make, shade & design over the purlins with necessary screw. C) GUTTER (Dongue): Providing & fixing standard thick polycarbonate or PVC Gutter with necessary m.s. frame work on the free end. The rate quoted shall include the cost of providing & applying two coats of 1st quality synthetic enamel paint over a coat of metal primer on entire MS framing, providing & grouting the base plate of vertical posts with heavy type 8nos. screw / nut & fastener, providing & fixing providing 150 mm lap with adjacent sheet while fixing, lifting, scaffolding, providing & filling the gap between wall & new shed with approved quality silicon, disposing off the debris out of Banks premises etc. all complete as directed by Banks Engineer-in-Charge. (Plan area measurement will be taken for payment) (Basic rate of 4 mm thick polycarbonate sheet =Rs.1680/- per Sqm excluding GST) (Approx. dimension, Width = 4.6, Length = 37 m, Height= 4.0 m) Sketch / Drawing : Original Text : Not attached. Revised Text : Attached sketch CGM (OIC) for West Bengal |